Case and Fan Layout for a Custom PC Build: A Whitburn Guide

The case and its fans decide how hot and how loud a custom PC runs for the next five years, and they are the parts most first-time builders pick last. Here is the bench order we work through when a Whitburn customer asks us to plan a new build around them.

12 November 2026 7 min read Custom Builds Alex M.
Case and fan layout for a custom PC build, a Whitburn guide from PC Repair Services

A Whitburn customer brought us a brand-new build last autumn that had been assembled in a glass-fronted case with two small 120 mm intakes and one rear exhaust. The CPU was sitting twenty degrees warmer than it should at idle, the graphics card throttled within five minutes of any game loading, and the fans sounded like a cheap vacuum cleaner the whole time it was on. Nothing in the parts list was faulty — the CPU, the cooler and the GPU were all fine. The case and the fan layout had been chosen last, from a shortlist of what looked nice, and they were the reason the machine was unusable. This guide is the order we work through on the EH11 bench when a Whitburn, Uphall or Livingston customer wants a case and a fan plan that will keep a custom PC build cool and quiet for years, not weeks.

Why the Case and Fans Deserve Picking First

The case is treated as a finishing decision by most first-time builders, picked for the look on the shelf and the RGB on the box. On the bench it is the opposite: the case is what every other part has to fit, cool and cable through, so picking it last forces every later decision into a compromise. A tower air cooler that is five millimetres too tall; a graphics card that is fifteen millimetres longer than the case supports; an all-in-one radiator that technically fits but leaves no room for its tubing; a power supply with cables too stiff to tuck behind the motherboard tray — all of these are issues we see weekly on builds brought in half-assembled. Decide the case and its fan layout first, and the parts list writes itself around something that will actually work.

The fans matter in the same way. A case ships with a token one or two fans on cheaper models, and those are almost always the fans people then run the build with. Replacing or supplementing them during assembly — rather than six months later when the first summer reveals the temperatures — is one of the cheapest upgrades in a modern build, and one of the few that genuinely changes how the finished machine feels to live with.

Case Size: ATX Mid-Tower Earns Its Place

The size debate usually goes one of three ways. A Mini-ITX case is tempting for a small desk, but the trade-offs are real: short graphics cards only, limited radiator support, one or two fan mounts in total, and almost no room for cable management, which makes airflow worse before a fan is added. Micro-ATX saves a little desk space over ATX and keeps most of the radiator and cooler options open. A full-tower is usually a solution looking for a problem on a home build; it swallows desk space for GPU length or radiator sizes that a current mid-tower already supports comfortably.

For the vast majority of Whitburn and West Lothian builds we spec, an ATX mid-tower is the honest default. It takes any sensible CPU cooler, any current graphics card, a 280 mm or 360 mm radiator at the top or front, enough fan mounts to shape airflow properly, and enough room behind the motherboard tray to run cables without pinching them against the side panel. A build that needs to fit under a desk in a small flat has its own set of trade-offs, which our earlier guide to planning a custom PC build for a small flat walks through; outside that constraint, pick the mid-tower.

Mesh at the Front, Glass on the Side

The single decision that separates a case that breathes from one that cooks itself is the front panel. A tempered-glass front looks beautiful on the shelf and suffocates the build inside it; the fans can only pull in air through whatever narrow gap the designer left between the glass and the frame, and the result on the bench reliably measures five to ten degrees warmer at the CPU and GPU compared to the same components in a mesh-fronted case. Side glass is fine, because no air is supposed to move through the side panel; it is the front panel — where the intake fans live — that must be mesh.

Dust filters belong on every intake, which in a sensibly laid-out case means a magnetic mesh filter on the front and another on the bottom under the power supply. They collect enough fluff in a flat with pets or carpet that a monthly rinse under the tap is a genuine piece of maintenance; a build without filters pulls that same fluff onto the heatsinks instead, and that is where the “my PC is quieter after you cleaned it” comment on our collection notes comes from.

Front, Top and Back: Where Fans Actually Belong

Hot air rises, and almost every mistake we see in a fan layout ignores that. The honest rule for a mid-tower is simple: fans at the front pull cool air in through the mesh and the dust filter, fans at the top push hot air out, and the single fan at the back takes the warm air coming off the CPU cooler and sends it out with the top exhausts. The bottom of the case, under the power supply, is a filtered intake and usually does not need its own fan.

Two or three intakes at the front and one or two exhausts at the top-plus-rear is the shape that works for most ATX mid-tower builds. The common mistakes are putting fans on the top panel as intakes (they fight the natural rise of hot air), running the rear fan as an intake (it pulls warm exhaust back into the case), and installing a side-panel fan on an already-tight case (it disrupts the front-to-back flow rather than helping it). If an all-in-one liquid cooler is going in, the radiator belongs at the front or the top; mounting it at the front gives the CPU the coolest air and is the honest default, mounting it at the top is fine when the graphics card runs hot and the radiator is small enough not to crowd the motherboard.

Bigger and Slower Is Quieter Than Small and Fast

The fan trade-off that matters most for noise is size against speed. A 140 mm fan at 800 RPM moves roughly the same volume of air per minute as a 120 mm fan at 1300 RPM, and it does so noticeably more quietly, because the bearing and the blade tips are turning slower. Where a case supports 140 mm fans at the front, fit them; the noise difference at full load is the gap between a machine you can hear from the sofa and one you cannot. For radiators, a 280 mm (two 140 mm fans) is almost always a quieter choice than a 240 mm (two 120 mm fans) for the same CPU, and a 360 mm is quieter still under sustained load.

Pulse-width-modulation (PWM) fans are worth the small premium over three-pin voltage-controlled ones, because the motherboard can then ramp them with the temperatures rather than running them at a single flat speed all day. A sensible fan curve — silent below sixty degrees, lifting gradually through to full speed at eighty — is the difference between a build that sits at thirty decibels at the desk and one that holds forty-five under a long export or a long gaming session.

Positive, Negative or Balanced Pressure

Case pressure is the term for whether the intake fans move more air in than the exhaust fans move out, or the other way round. Positive pressure (more intake than exhaust) pushes air out through every unsealed gap, which keeps dust out because all the incoming air is going through the filters. Negative pressure (more exhaust than intake) pulls air in through every gap, filter or not, and the dust collects on every internal surface. Balanced pressure sits between the two.

For a build in a flat with carpet, pets or an open window near a road, slightly positive pressure is the honest choice: three front intakes and two top-or-rear exhausts, or two front intakes and one rear exhaust, rather than the symmetrical layout the case manual tends to show. For a build in a clean office, balanced is fine. Pure negative pressure is almost never the right answer in a home environment; after a year the machine looks the inside of a long-haul lorry’s radiator.

Common Mistakes We See on Half-Built Machines

Four patterns turn up on the bench every month when a part-finished build comes in for us to sort out. The first is a glass front panel on a gaming build — always a case swap, never a fix inside the case. The second is a 240 mm all-in-one on a modern high-core CPU, which runs warmer than the same CPU on a good 120 mm tower air cooler because the pump has too little radiator to shed into. The third is cables run across the front intake path, which strangle the airflow the fans were chosen for; good cable management is a thermal decision, not a cosmetic one. The fourth is an un-filtered build run for a year next to a pet bed, where a desktop PC repair that was supposed to be about crashing turns out to be a fur blanket on the CPU cooler, visible across a torch beam before the side panel is even off. For readers starting from a parts list drawn up online, the compatibility traps we keep seeing (and how to avoid them) are covered in our guide to PC build parts that don’t fit together.

Where We Fit In, for a Whitburn Build

For customers across Whitburn, Uphall, Bathgate, Livingston and the wider A89 commuter belt, we handle these builds end-to-end from the EH11 workshop: a sit-down to understand how the machine will actually be used, a written parts list that starts with the case and the fan layout and then fills in the components they must support, assembly and burn-in testing on the bench rather than at your desk, and a handover back in Whitburn with the fan curve tuned so the machine is quiet at idle and under load alike. For a desktop that already exists and just needs its airflow or cooling fixed rather than replacing, the same bench covers it as a desktop PC repair and upgrade appointment, and larger cooler or fan upgrades fall under our hardware upgrades service. For planning a first build from scratch, our first custom PC build guide walks through the earlier planning steps, and the silent home-office PC build guide goes further on noise for sound-sensitive rooms. The Whitburn custom PC build page has the collection and workshop drop-off details for the local area.

A case and its fans are not finishing touches; they are the framework the rest of a custom PC either works inside or fights against. Pick the case first, make it mesh at the front, lay the fans out front-in and top-plus-rear-out, favour size over speed, keep the pressure slightly positive, and the finished machine will stay quiet and cool long after the novelty of a new build has worn off. If you are planning a build in Whitburn or anywhere across West Lothian, bring the shortlist in and we will walk through the case and the fan plan before a single component is ordered.

Last updated: 12 November 2026

Frequently Asked Questions

What Whitburn and West Lothian customers ask us about PC cases and fan layouts.

Yes, and the gap is bigger than most product reviews suggest. On the bench we see the same components running five to ten degrees warmer at the CPU and the GPU in a tempered-glass front case than in a mesh-fronted equivalent, because the intake fans can only pull air through whatever slot is left between the glass and the frame. Side glass is fine; front glass is a cosmetic choice that costs a real amount of thermal headroom.

For a sensible ATX mid-tower build, two or three intakes at the front and one or two exhausts split between the top and rear is the layout that works for the vast majority of home PCs. More fans than that tends to add noise without adding meaningful airflow, especially once the case is already well-balanced. A fan-controller or a motherboard PWM header set up properly matters more than raw fan count.

Always an exhaust. The rear fan sits directly behind the CPU air cooler and its job is to pull the warm air the cooler has shed out of the case, together with the top-panel exhausts. Running it as an intake pulls the warm exhaust back in and makes the CPU temperature worse; it is one of the common mistakes we see on half-built machines brought in for a check-over.

RGB is a lighting decision, not a cooling one. A well-made RGB fan from a reputable brand moves air and keeps noise down as well as any non-RGB equivalent in the same tier. Cheaper RGB fans tend to use noisier bearings, so the ones at the budget end of the shelf often are louder — but the colour is not the cause. Pick on airflow, bearing type and warranty first, and the lighting as an aesthetic preference afterwards.

Usually yes. A great many of the overheating desktop repairs we take in from Whitburn, Uphall and Livingston turn out to be fan swaps and a fan-curve tune rather than any component replacement. Bring the machine into the EH11 workshop and we will measure the temperatures as they are, suggest the fan changes that will move the needle, and fit them on the bench with a clean dust strip while the case is open.

Planning a Custom PC in Whitburn?

Bring the parts shortlist into the EH11 workshop or book a collection across Whitburn, Uphall, Bathgate and Livingston. We start with the case and the fan layout, build and burn-in on the bench, and tune the fan curves before the machine leaves so the finished build is quiet at the desk and cool under load.